Labs / Electronic modules

GraftSense-XH2.54 to Grove Adapter Board (Open Version)

Author: Li Zisheng · Source: FreakStudio open documentation, v1.1 · License: CC BY 4.0

Contents
XH2.54
GraftSense-XH2.54 XH-2.54 LED1 U1 C1 C2 C3 C4 XH2.54 V1.0.0

I. Module Introduction

XH2.54 to Grove Adapter Board is an adapter module for interface conversion, which enables XH2.54 interface and Grove interface to transfer signals and power. It is compatible with equipment such as water immersion modules, electronic water gauge liquid level sensors, soil temperature and humidity sensors, and frost freezing sensors; the module is equipped with LDO voltage regulator circuit, power filtering and power indicator light, supports 3.3V power supply, adapts to the connection of sensors and main control boards with different interface standards, and provides a convenient signal and power transfer solution for devices with different interfaces.

II. Introduction to Main Chips

2.1 Chip Overview

None.

2.2 Pin Definition

2.2.1 Capacitive Dust, Rain and Frost Sensor CDS1081

CDS1081 CDS-MCP1081 V1.0 BA23582 VCC8 MCP1081S
CDS1081 5V 2V 5.5V

2.2.2 FDE Sensor Frost and Ice Sensor

C1 C2 C3 V3.0
GraftSense-XH2.54 to Grove Adapter Board (Open Version)

2.2.3 Water Immersion Module WS61

WS61 GraftSense-XH2.54 V1.0
GraftSense-XH2.54

2.2.4 MER-MCP1081-260-26 Electronic Staff Gauge Liquid Level Sensor

RX/RS485-A TX/RS485-B 2.3V 5.5V

Note: The image above is a screenshot from the manual, and the wiring instructions in this screenshot do not match the markings on the actual product. The image below shows the actual product: the green wire connects to the RX of the host computer, and the yellow wire connects to the TX of the host computer. Please refer to the markings on the actual product for accuracy.

GraftSense-XH2.54 MER20A251110007

2.2.5 MSE Low-Cost Soil Temperature and Humidity Sensor

0 60 5
GraftSense-XH2.54 to Grove Adapter Board (Open Version)

2.3 Functional Block Diagram

None.

2.4 Performance Parameters

None.

2.5 Reference Circuit

None.

2.6 Chip Configuration

None.

None.

2.8 PCB Routing Precautions

None.

III. Circuit Engineering

3.1 Circuit Source Engineering

To obtain the source code of the circuit, please follow the official account [Freak Embedded]

3.2 Module Usage Instructions

The schematic diagram of this module is shown below:

SCH_Schematic1_XH2.54 to Grove Adapter Board-v1.0.0_2026-05-07.pdf 2.5 MB

GraftSense-XH2.54 XH2.54 V1.0.0 XH-2.54 LED1 R1 U1 C1

This module provides a serial port UART interface MRX and MTX: where M stands for master, meaning the MCU 's RX corresponds to the TX of this module.

3.3 Application Experiment

This module is an adapter board for the Minsensor sensor module. For specific usage, please refer to:

Capacitive Dust, Rain and Frost Sensor CDS1081

FDE Sensor Frost and Freeze Sensor

Water Immersion Module WS61

MER-MCP1081-260-26 Electronic Staff Gauge Liquid Level Sensor

Low-cost soil temperature and humidity sensor MSE

IV. Drivers

None.

None.

VI. Revision History

Document Version

Date Modified

Modifier

Modify Content

v1.0

2026-05-07

Ling Gaoxing

Initialize the document

v1.1

2026-06-05

Xin Ruili

Create an open version of the document based on the internal document version v1.1.

7. Relevant Materials

7.1 Chip Datasheet

WS61 Water Immersion Sensor Product Introduction-Minyuan 202506-2.pdf 1.2 MB

CDS1081 Capacitive Dust, Rain and Frost Sensor Product Introduction-Minyuan 202603-2.pdf 765 KB

FDE+Sensor_Frost_and_Ice_Sensor_Product_Brief-Minyuan_202512-2.pdf 733 KB

MER-MCP1081-260-26 Electronic Water Gauge Level Sensor Product Manual-Minyuan 202601.pdf 896 KB

MSE Low-Cost Soil Temperature and Humidity Sensor Product Manual-Minyuan 202410.pdf 864 KB

7.2 Unique Icons for PCB Silk Screen

GraftSense-XH2.54